|
Builders’ Tip: How to Fix Warped Cabinet Doors
|
|
 |
|
|
 |
|
|
Click for larger image. | A warped cabinet door can be a real pain. When you have spent hours matching panels, colors and grains, the last thing you want to do is remake a door.
My approach takes a couple of hours and $5 in materials.
I make a U-shaped spring, or torsion bar, out of music wire and insert it into the door (see accompanying drawing). Music wire is commonly available in hardware stores and is much stiffer than regular mild-steel rods.
- The first step is to lay the panels out for drilling into the end grain of the stiles to miss any hinges or other hardware. Once you’ve marked the panel centers, don’t begin drilling until you’ve made the torsion bar. If the distance between the steel legs varies a bit, you can shift the holes accordingly.
It’s easier to make the holes match the steel than to try to bend the steel to an exact dimension.
- To make the torsion bar, you need music wire and a torch. Ordinary propane torches really don’t work. MAPP gas or oxy-acetylene torches are the best choices. Also, be sure to have a fire extinguisher nearby when using the torch.
For a 3/4-inch thick cabinet door, I recommend using 3/16-inch music wire. Drill the holes 1/4 inch, otherwise it will be too much of a struggle to fit the spring.
Clamp the wire in a vise, leaving the leg long ― 7 inches to 8 inches. Bring the wire to an orange heat and, with pliers, bend the leg to a 90-degree angle.
Finish the corner with a light hammer blow or two to square it up and let it cool slowly. Don’t chill or quench the bend. If you do, the steel will become brittle and can snap.
- Using the dimension from the layout marks on your door, locate the bending point of the opposite leg.
Now for the fun part. The idea is to offset the legs from each other so that when they are inserted in the door they twist against the warp.
- Bend the second leg offset to your best guess. Then, using a Dremel tool or grinder, cut off the legs to fit the depth of the holes you will drill in the stiles.
Don’t try using a bolt cutter on music wire unless you really want to buy a new one.
- Now, bore the door using a doweling jig and a bell-hanger bit available at most hardware stores.
For a typical door, I bore in about 5 inches to 6 inches to provide the leverage required. With careful drilling, you can get this far fairly easily, even in a thin door. For thicker doors, you can use thicker wire or more offset as required.
- After boring, I use a router and a splining bit to rout a channel between the holes for the middle section of the torsion bar. Slip it in for a test fit, with a tape loop or string underneath to pull it out.
The door may fit on the first try, or you may need to increase or decrease the spring tension by heating and re-bending. A dab of hot glue or epoxy will hold the spring in place.
If the door shifts again after a bit of time, you can remove the spring and adjust it.
— Gregg Roos, San Francisco
Tips & Techniques provided by Fine Homebuilding.
©2008 The Taunton Press
To contact Fine Homebuilding, e-mail Christina Glennon.
 Set Yourself Apart With CGB Designation
Join the ranks of the nation’s top building industry professionals with the Certified Graduate Builder (CGB) designation. The “Builder Assessment Review” (BAR) is your first step towards obtaining the CGB.
This comprehensive assessment measures your expertise in the four key areas of the building industry: building technology, business and finance, project management and sales and marketing.
Your results will show the areas where your knowledge is strongest and weakest and will help determine the courses required for you to obtain your CGB.
To learn where the next BAR will be held, visit NAHB’s education listings, or call the Professional Designation Help Line at 800-368-5242 x8154.
 BuilderBooks.com Offers More Than 250 Books That Help You Build Your Business
BuilderBooks.com is your source for training and education products for the building industry. The official bookstore for NAHB, BuilderBooks.com offers award-winning publications, software, brochures and more available in both English and Spanish.
To view these publications online, click here, or call 800-223-2665.
 Free NAHB Kit Gives Builders Back-to-Basics Tips to Navigate the Slowdown
What was once expected to be a relatively mild housing slump following three years of record new home construction and sales has given way to a significant downturn.
To help members navigate the uncharted waters of this slowdown, NAHB has compiled a comprehensive “Back to Basics” online toolkit — the best of the basics, the tried and true and the truly new. To access the toolkit, click here.
To access the “Back to Basics” toolkit, you must be an NAHB member and have a login to www.nahb.org. To create a login, go to www.nahb.org/login or click on the log-in button on the main menu bar.
For assistance, call the NAHB Member Service Center at 800-368-5242.
|
